1. Feature and Advantage
Sightseeing Mini Eletric Track Train / Locomotive with 15 Seats
Manufacturer for Amusement Rides Mini Diesel Track Train with High quality & conpetitive price you. Customer is welcome to visit our new showroom and factory located in HangZhou City, China.
DST05-2X-15 Sightseeing Mini Eletric Track Train
Marshalling: locomotive + passenger car*5
Mat limit slope: 30 per thousand
Restriction curve radius: 5m
Power: Storage battery
2.1 Ambient conditions and vehicle parameters
1) Project location height is not more than 2000 meters above sea level.
2) The air temperature is between -10 and 40 degree.
3) No outdoor operation in rainy days.
4) Carriage should be CZPT to withstand wind and sand intrusion and salt fog corrosion.
5) Line gauge:254mm
6) Limiting gradient:30‰
7) Minimum railway curve radius: 5m
2.2 Vehicle parameters
1) Gauge: 254mm (10 inches)
2) Grouping: locomotives + cars + cars + cars + cars + cars
3) Overall dimensions: 8.2m (length) x 0.5m (width) x 0.78m (height);
4) Personnel: 15 (including driver 1 person)
5) Speed: 7km/H
6) Limit slope: 30‰
7) Minimum curve radius: 5m
8) Emergency braking distance: <0.5m at the highest speed
9) No outdoor operation in rainy days
10) Dimensions: 1.2m*0.5m*0.78m
11) Power: Maintenance-free battery pack 48v 65AH (two pieces)
12) Drive motor: 1500w motor
13) Speed control method: V-F frequency conversion speed regulation S-curve acceleration.
14) Voltage: Control voltage, lighting voltage: 24V (safety voltage),
15) Working brake: DC braking, dynamic braking; emergency braking: Electropneumatic braking.
16) Driver’s seat: one-way seated
17) Cold Steam Smoke Effect, Air Flute
18) Overall dimensions 1.2m*0.5*0.6m
19) Seats: 3 seats per section
20) Shock absorption: metal coil spring
21) Braking: Electropneumatic Combined Braking
2.3 Company profile
HangZhou dising technologies Co., Ltd. is located in the east lake new technology development zone in HangZhou, ZheJiang province.It is a professional supplier of tourist attraction, theme park, characteristic town, and commercial block slow rail transit system;Our service covers the whole process of slow rail transit system survey and design, special track vehicle design and so on.
We promise to improve our professional skills and be based on a careful design attitude, a profound understanding of customer needs and a rich experience in project implementation, to provide customers with high quality and reliable products and economic and reasonable projects.
2.4 Products Series
In the years of industry experience, the company created the ZheJiang tenyun steam locomotive replica plate, the Tianya corner scenic spot in ZheJiang , the HangZhou Yuet square project, the tram, the ZheJiang lling National Agricultural Park sightseeing train, the Xihu (West Lake) Dis. Lu Jia Village sightseeing small train and so on. The main products covers 3 kinds of landscapes:tourism. Sightseeing trains, sightseeing trams and locomotives 3 kinds of landscapes.
1. Electric Train Sets
2. Electric Locomotive
3. Fun Train
4. Sightseeing Mini Train
2.5 Delivery and Shipment
Shipping by sea: Around 4 weeks to arrive.
Delivery Time: Around 30 working days after receipt of deposit.
MOQ: 1 set.
Payment Term: 30% T/T deposit, 70% T/T before delivery.
Mini Electric Trackless Train for Tourist: 1 year full warranty,offer FREE components under EXW shipped term.
Oversea Engineer After Sale Service Availbale.
Q1. What is your terms of packing?
A: Generally, we pack our goods in neutral white boxes and brown cartons. If you have legally registered patent, we can pack the goods in your branded boxes after getting your authorization letters.
Q2. What is your terms of payment?
A: T/T 30% as deposit, and 70% before delivery. We’ll show you the photos of the products and packages before you pay the balance.
Q3. What is your terms of delivery?
A: EXW, FOB, CFR, CIF, DDU.
Q4. How about your delivery time?
A: Generally, it will take 30 to 60 days after receiving your advance payment. The specific delivery time depends on the items and the quantity of your order.
Q5. Can you produce according to the samples?
A: Yes, we can produce by your samples or technical drawings. We can build the molds and fixtures.
Q6. What is your sample policy?
A: We can supply the sample if we have ready parts in stock, but the customers have to pay the sample cost and the courier cost.
Q7. Do you test all your goods before delivery?
A: Yes, we have 100% test before delivery
Q8: How do you make our business long-term and good relationship?
A:1. We keep good quality and competitive price to ensure our customers benefit ;
2. We respect every customer as our friend and we sincerely do business and make friends with them, no matter where they come from.
Worm Gear Motors
Worm gear motors are often preferred for quieter operation because of the smooth sliding motion of the worm shaft. Unlike gear motors with teeth, which may click as the worm turns, worm gear motors can be installed in a quiet area. In this article, we will talk about the CZPT whirling process and the various types of worms available. We’ll also discuss the benefits of worm gear motors and worm wheel.
In the case of a worm gear, the axial pitch of the ring pinion of the corresponding revolving worm is equal to the circular pitch of the mating revolving pinion of the worm gear. A worm with 1 start is known as a worm with a lead. This leads to a smaller worm wheel. Worms can work in tight spaces because of their small profile.
Generally, a worm gear has high efficiency, but there are a few disadvantages. Worm gears are not recommended for high-heat applications because of their high level of rubbing. A full-fluid lubricant film and the low wear level of the gear reduce friction and wear. Worm gears also have a lower wear rate than a standard gear. The worm shaft and worm gear is also more efficient than a standard gear.
The worm gear shaft is cradled within a self-aligning bearing block that is attached to the gearbox casing. The eccentric housing has radial bearings on both ends, enabling it to engage with the worm gear wheel. The drive is transferred to the worm gear shaft through bevel gears 13A, 1 fixed at the ends of the worm gear shaft and the other in the center of the cross-shaft.
In a worm gearbox, the pinion or worm gear is centered between a geared cylinder and a worm shaft. The worm gear shaft is supported at either end by a radial thrust bearing. A gearbox’s cross-shaft is fixed to a suitable drive means and pivotally attached to the worm wheel. The input drive is transferred to the worm gear shaft 10 through bevel gears 13A, 1 of which is fixed to the end of the worm gear shaft and the other at the centre of the cross-shaft.
Worms and worm wheels are available in several materials. The worm wheel is made of bronze alloy, aluminum, or steel. Aluminum bronze worm wheels are a good choice for high-speed applications. Cast iron worm wheels are cheap and suitable for light loads. MC nylon worm wheels are highly wear-resistant and machinable. Aluminum bronze worm wheels are available and are good for applications with severe wear conditions.
When designing a worm wheel, it is vital to determine the correct lubricant for the worm shaft and a corresponding worm wheel. A suitable lubricant should have a kinematic viscosity of 300 mm2/s and be used for worm wheel sleeve bearings. The worm wheel and worm shaft should be properly lubricated to ensure their longevity.
A multi-start worm gear screw jack combines the benefits of multiple starts with linear output speeds. The multi-start worm shaft reduces the effects of single start worms and large ratio gears. Both types of worm gears have a reversible worm that can be reversed or stopped by hand, depending on the application. The worm gear’s self-locking ability depends on the lead angle, pressure angle, and friction coefficient.
A single-start worm has a single thread running the length of its shaft. The worm advances 1 tooth per revolution. A multi-start worm has multiple threads in each of its threads. The gear reduction on a multi-start worm is equal to the number of teeth on the gear minus the number of starts on the worm shaft. In general, a multi-start worm has 2 or 3 threads.
Worm gears can be quieter than other types of gears because the worm shaft glides rather than clicking. This makes them an excellent choice for applications where noise is a concern. Worm gears can be made of softer material, making them more noise-tolerant. In addition, they can withstand shock loads. Compared to gears with toothed teeth, worm gears have a lower noise and vibration rate.
CZPT whirling process
The CZPT whirling process for worm shafts raises the bar for precision gear machining in small to medium production volumes. The CZPT whirling process reduces thread rolling, increases worm quality, and offers reduced cycle times. The CZPT LWN-90 whirling machine features a steel bed, programmable force tailstock, and five-axis interpolation for increased accuracy and quality.
Its 4,000-rpm, 5-kW whirling spindle produces worms and various types of screws. Its outer diameters are up to 2.5 inches, while its length is up to 20 inches. Its dry-cutting process uses a vortex tube to deliver chilled compressed air to the cutting point. Oil is also added to the mixture. The worm shafts produced are free of undercuts, reducing the amount of machining required.
Induction hardening is a process that takes advantage of the whirling process. The induction hardening process utilizes alternating current (AC) to cause eddy currents in metallic objects. The higher the frequency, the higher the surface temperature. The electrical frequency is monitored through sensors to prevent overheating. Induction heating is programmable so that only certain parts of the worm shaft will harden.
Common tangent at an arbitrary point on both surfaces of the worm wheel
A worm gear consists of 2 helical segments with a helix angle equal to 90 degrees. This shape allows the worm to rotate with more than 1 tooth per rotation. A worm’s helix angle is usually close to 90 degrees and the body length is fairly long in the axial direction. A worm gear with a lead angle g has similar properties as a screw gear with a helix angle of 90 degrees.
The axial cross section of a worm gear is not conventionally trapezoidal. Instead, the linear part of the oblique side is replaced by cycloid curves. These curves have a common tangent near the pitch line. The worm wheel is then formed by gear cutting, resulting in a gear with 2 meshing surfaces. This worm gear can rotate at high speeds and still operate quietly.
A worm wheel with a cycloid pitch is a more efficient worm gear. It reduces friction between the worm and the gear, resulting in greater durability, improved operating efficiency, and reduced noise. This pitch line also helps the worm wheel engage more evenly and smoothly. Moreover, it prevents interference with their appearance. It also makes worm wheel and gear engagement smoother.
Calculation of worm shaft deflection
There are several methods for calculating worm shaft deflection, and each method has its own set of disadvantages. These commonly used methods provide good approximations but are inadequate for determining the actual worm shaft deflection. For example, these methods do not account for the geometric modifications to the worm, such as its helical winding of teeth. Furthermore, they overestimate the stiffening effect of the gearing. Hence, efficient thin worm shaft designs require other approaches.
Fortunately, several methods exist to determine the maximum worm shaft deflection. These methods use the finite element method, and include boundary conditions and parameter calculations. Here, we look at a couple of methods. The first method, DIN 3996, calculates the maximum worm shaft deflection based on the test results, while the second one, AGMA 6022, uses the root diameter of the worm as the equivalent bending diameter.
The second method focuses on the basic parameters of worm gearing. We’ll take a closer look at each. We’ll examine worm gearing teeth and the geometric factors that influence them. Commonly, the range of worm gearing teeth is 1 to four, but it can be as large as twelve. Choosing the teeth should depend on optimization requirements, including efficiency and weight. For example, if a worm gearing needs to be smaller than the previous model, then a small number of teeth will suffice.